GE
Appliance Repair

A GE fridge that stops cooling is rarely a $700 job.

That is what our own billing shows. The median GE refrigerator repair we completed came to about $385, against $450 for refrigerators of every other brand we fix. Only 3% of GE fridge repairs reached $700; for the other brands it was 29%.

The reason is in the notes. In the GE refrigerator write-ups we went through for this page, the faults were control boards, inverter boards, fans, defrost parts and condenser coils packed with dirt. None was a compressor replacement. Here are three GE fridges from three different towns, and three different answers.

54.1°Ffresh-food shelves, on our infrared thermometer

About $400

October 2025 · Sherman Oaks · GE Profile French door

Warm in both sections, and the fix was a board

The owner said the fridge had stopped cooling, and the thermometer agreed. The fresh-food shelves read 54.1°F, well over the 40°F ceiling that food-safety guidance sets. Ice-cream tubs in the freezer basket read 49.2°F. The control panel on the ceiling of the fresh-food compartment showed 47 under Freezer and “tc” under Refrigerator. The model, from the rating label, was a GE Profile PFCS1NFXB.

Our technician traced it to a faulty inverter assembly, the board that powers the compressor, and replaced it. The bill was about $400, with a return-customer discount applied.

Board + coilsa failed main control board, and a compartment matted with lint

About $635

October 2025 · Moorpark · GE Profile side-by-side

A white GE Profile that had stopped cooling

This was a white side-by-side with a door dispenser, model PSF26MGWA. The main control board had failed, and with it the cooling system had stopped working properly. We replaced the board with a new OEM part.

With the back panel off, the lower compartment was matted with grey lint and dust, so the condenser coils were cleaned in the same visit. The fridge was tested afterwards and was cooling again. The bill was about $635, the highest of the jobs on this page.

37°Fdial thermometer in the fresh-food section on the first visit

$87.85, then $226.90 in October

June 2026 · Downtown Los Angeles · GE Profile bottom freezer

Re-seated drawers, then a second call four months on

The booking said the fridge had got too cold and the vegetables were freezing. Our technician checked both compartments first, and both were in the normal range. The thermometer in the fresh-food section sat at about 37°F.

The cause was the crisper drawers. They had been put back out of position, which changed how the cold air flowed into the drawer area. Our technician re-seated them, checked the fit and the airflow, and found nothing else wrong that day. Nothing had to be ordered or fitted; the invoice was $87.85, the diagnostic.

That was not the end of it. In late October 2026 the same customer booked us again for this GE Profile: very loud, and freezing food in the fresh-food section. That second visit was completed and billed $226.90. Its technician notes are blank, so we can’t tell you here what was found or which part went in, only that the drawer fix had not settled the problem.

GE washers come in full of water, not flashing a code.

When a GE washer owner books with us, the complaint we hear most is water that will not leave the drum. “Not draining” is in about half of the GE washer bookings that describe the fault, against about three in ten for other washer brands. “Not spinning or not agitating” comes up about twice as often, 29% against 15%. GE owners almost never quote an error code (2% of those bookings, against 23% for other brands), so a description of what the machine is doing helps us most.

A typical case: a GE washer in Newbury Park (Thousand Oaks), March 2026, that would not drain. The drain pump assembly had failed. We fitted a new pump, reconnected the hoses and wiring, checked for leaks and ran it through drain and spin. About $400. That is close to our median GE washer bill of about $375, about the same as for other brands.

Not every GE washer ends with a fix. A GE front-load washer in Culver City did not. Our record for that job closes at $87.85, the diagnostic. Its owner explained why on Google:

★★★★★

“Our GE front-load washer developed a very unusual electrical issue that eventually left it unable to complete cycles. What stood out to me was the amount of effort this company put into trying to solve the problem. The technician came out on four separate days, spent hours diagnosing the washer, tested multiple components, installed replacement parts, and kept us informed throughout the entire process.

The repair turned into a moving target. As one issue was addressed, another symptom appeared, and they even waived additional labor during this process. Eventually, a brand-new replacement control board itself suffered damage during testing (not their fault, faulty part or wiring in our machine). At that point, it became clear we had reached a dead end where continuing to replace parts (and spending more time) would not be the most practical or cost-effective solution for either party.

This is where they really earned my trust. Instead of trying to continue to charge us for additional labor, parts, and visits, they were completely upfront about the situation. They refunded nearly all of the charges and only kept the original diagnostic fee, despite the significant amount of time, effort, and expertise they had already invested.

In an industry where it would have been easy to try to bill for more repairs, they chose honesty and fairness. They even took the time to explain which parts were still worth keeping if we replaced the washer with the same model in the future.

While we ultimately decided to replace the machine, I left with a tremendous amount of respect for this company. They were professional, transparent, and genuinely put the customer’s best interests first. I would absolutely call them again and highly recommend them to anyone looking for an honest appliance repair company.”

Victor K.Google, June 2026 · GE front-load washer, Culver City

What you can count on, whatever the GE.